2. CABLE CONNECTION

2-1. Before Connecting

Before connecting your monitor to the PC, change the display screen settings (resolution and frequency) in accordance with the charts below.

 

*
The lower display modes like 640x 480, automatically enlarge to the maximum display mode (1280 x 1024), and some lines of the characters may become fuzzy. In this case, use <Smoothing> function to make the lines clear.
*
When your computer and display support VESA DDC, the suitable resolution and the refresh rate are set by just plugging your display into the computer without any manual settings.

 

Analog Input

Resolution
Frequency
Dot Clock
Remarks
320 × 200
70 Hz
135 MHz
(Max.)
VGA Graphic
640 × 480
~ 75 Hz
VGA, VESA
640 × 480
67 Hz
Apple Macintosh
720 × 400
70 Hz
VGA TEXT
800 × 600
~ 75 Hz
VESA
832 × 624
75 Hz
Apple Macintosh
1024 × 768
~ 75 Hz
VESA
1152 x 864
75 Hz
VESA
1152 x 870
75 Hz
Apple Macintosh
1280 x 960
60 Hz
VESA
1280 x 960
75 Hz
Apple Macintosh
1280 x 1024
~ 75 Hz
VESA

 

Digital Input

The monitor supports the following resolutions only.

Resolution
Frequency
Dot Clock
Remarks
640 × 480
60 Hz
108 MHz
(Max.)
VGA
720 × 400
70 Hz
VGA TEXT
720 × 480
60 Hz
VESA Safe Mode
800 × 600
60 Hz
VESA
1024 × 768
60 Hz
VESA
1280 x 1024
60 Hz
VESA

 

2-2. Connecting the Signal Cable

*
Before connecting the product, set up the monitor after unfolding the base of the stand. (Height adjustable stand version only)
*
Be sure that the power switches of both the PC and the monitor are OFF.

 

1.

Plug the signal cable into the connector at the rear of the monitor and the other end of the cable into the video connector on the PC.

After connecting, secure the connection with the screw-in fasteners.

 

Analog Input

Signal Cable
Connector of the PC
PC
Signal Cable (enclosed) Video Output Connector/ D-Sub mini 15 pin Standard graphics card Macintosh G3 (Blue & White) / G4 (VGA)
Signal Cable (enclosed) + Adapter (Optional) Video Output Connector D-Sub 15 pin Macintosh

 

Digital Input

Signal Cable Connector of the PC PC

FD-C04 /FD-C35/FD-C39 (Optional)

Video Output Connector/ DVI Macintosh (DVI)
Digital graphics card

 

*

The monitor is not compatible with a Power Mac G4/G4 Cube ADC (Apple Display Connector).

 

2.

Plug the power cord into the power connector on the rear of the monitor. Then, plug the other end of the cord into a power outlet.

WARNING

Use the enclosed power cord and connect to the standard power outlet of your country.

Be sure to remain within the rated voltage of the power cord.
Not doing so may result in fire or electric shock.

 


The equipment must be connected to a grounded main outlet.

Not doing so may result in fire or electric shock.


 

3.

Turn on the monitor's main power and then switch on the PC's power.

The monitor's power indicator will light up (blue).
If an image does not appear, refer to the "6. TROUBLESHOOTING" for advice.
Whenever finished, turn off the PC and the monitor.

 

*
Adjust brightness of the screen depending on the brightness of your environment. Too dark or too bright of a screen can cause eyestrain.
*
Be sure to take adequate rests. A 10-minute rest period each hour is suggested.

 

2-3. Connecting Two PCs to the Monitor

Two PCs can be connected to the monitor through the DVI and the D-Sub mini 15 pin connector on the back of the monitor.

 

Selecting the Active Input

The Input signal selection button on the front panel can be used to select either DVI or D-Sub as the active input at any time. Every time the button is pressed, the input changes. When switching the signal, the kind of the input signal (Analog or Digital) is displayed for a few seconds on the right top corner of the screen.

 

2-4. Sound Connections

*
Always switch the monitor and audio devices or computers off whenever connecting or disconnecting any audio devices (computer or CD player) to the monitor.
*
Use the enclosed stereo mini-jack cable for connecting audio devices or computers to the monitor.

 

1.

Connect the stereo mini-jack cable to the external line in of the monitor.

2.

Connect the other side of stereo mini-jack cable to the line out of audio devices.

Height adjustable stand version is given as an example.

 

Sound Control

Audio performance is available by connecting the headphone to the Headphone jack (When headphones are connected, no sound can be heard from the speakers).

 

Volume Control

Volume control

Press the Right and Left buttons.

Mute

Press the Up or Down button more than 2 seconds after pressing the Right or Left button to display the volume control bar.

Mute off

Press the Right or Left button.

 

*

<Sound> menu of the ScreenManager also controls the sound.